Return to Pumpers Homepage



12/11/96

Thanks to Brad & Troy for sending in these detailed directions for how to create your own weight system for stretching the penis. This device appears to be comfortable, is designed so that it won't slip off the penis, and distributes the weight evenly and comfortably.


TROY AND BRAD'S WEIGHT-SUSPENSION DEVICE FOR STRETCHING THE PENIS

 1.  Buy at least 1/2 yard of 2 inch velcro.  Cut a 4 long piece of"claw"
material and a 7 inch (minimum) piece of fuzzy material.  Arrange so that
looking down on these you see the back of  the "claw" (on your left) and the
front of the "fuzzy" (on your right).

     Diagram A. a 2" X 4" rectangle   Diagram B. a 2" X 7" rectangle
     Caption: Back of "claw"          Caption: Front of "fuzzy"


  2.  Now arrange the pieces so that there is a 2 inch overlap on the "claw" 
end. Backs of both pieces should be touching each other.  Sew or stitch
together.  Alternatively, you could  hot glue the two pieces together.

      Diagram C. A 2 X 9 rectangle - a solid line 2 inches 
                 from the left and a dashed line 4 inches from
                 the left

  3.  At the junction where the back of the "claw" meets the back of the
"fuzzy", sew the first metal ring in place.  It is best to place the rings in
the mid-position of the materials' width.  Do not use plastic rings (they'll
break).  Moving 1 and 1/2 inches to the right, sew the second ring in place (on
the front of the "fuzzy" material.  Moving again to the right  (approximately 1
and 1/2 inches) sew the third and final ring in place.  (Note: if done this
right, this 3rd ring will be the only one attached to "fuzzy" material alone.

      Diagram D. Same as diagram C,except there is a ring in the 
                 center of the solid line 2 inches from the left. The          
       others are spaced as per the instructions.

                          O    1.5"     O      1.5"    O

   4. "S" hooks and short chains (approximately 5 inches long) can be
permanently attached with pliers to each of the rings.   If you use chains, its
best that the one that will be directly over the head of the penis have  a
couple of extra links to distribute pull. This is really an option. You can use
elastic, leather, or regular cording (string) or a strong nylon filament.

      Diagram E. Same as D except that chains or cords are hanging             
    from each of the three rings.

   5. Using a piece of terry cloth (an old washcloth or towel     
approximately 2 inches by  12 inches in length, encircle the penis behind the
head.  If your velcro is wider, then cut this cloth wider. Do the wrap in a
semi-erect or fully flaccid state.  Now flip the velcro-ring device over 
(rings are now down and will be next to the terry cloth).  Wrap the device
snuggly in place.  You don't want to do this in a fully erect state; doing so
will  contribute to slippage.

  6.  You can now bring all three chains, straps, cords or whatever you've used
together and attach another "S=" hook and then attach the weight.  Start out
small with no more than 1 lb.  We recommend a program of four 15 minute
periods, 3 or 4 times a week.  That's a total of 1 hour with 2 to 3 minute
breaks after each of the 15 minute pulls.  Need to do this in the event you are
impairing circulation, in which case the head may become icy-cold.  Again, for
the novice, DON'T start out with too much weight.  Start out small and progress
upward over the next few weeks adding perhaps another 1/2 to 1 lbs. every
couple of weeks.   If at first, it hurts, then lessen the weight.  Attempts to
use too much weight until you get accustomed to the device will only add to
slippage. Five lbs. is  probably the upper limit, unless you're Hercules or a
hung like one of the Budweiser stallion.  Concerns have been expressed about an
hour glass shape of the penis following wearing weights.  This will disipate
within a short time and may even help compensate for the "donut" experienced
after pumping.  We are both cut with fairly firm, good size penis heads which
helps to prevent slippage.
   
    No idea whether this will work for those of you out there that are uncut.
Also remember that as opposed to pumping,  pull or stretch with the weights is
unidirectional.

    The main advantage of this velcro system is that you can keep  tightening
the device should slippage start to occur.

    So you can't sew.  Ask  your mother, wife or a girl friend that can to make
the device for you. If an explanation is necessary and you're a scuba diver,
say that you're fed up with 'D' rings and that you came across this neat hose
wrap for the attachment of light weight accessories.  So you don't dive, say
that its for the handlebars of your bike so that you can keep you keys, wallet,
etc.  readily available.  Come on guys, use your imagination...that's largely
why we're into all this isn't it.